qertops.blogg.se

1. SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK HOW TO
2. SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK INSTALL
3. SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK UPDATE
4. SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK WINDOWS 10
5. SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK FREE

(same notes apply as to the Docked X position values.) YPos and MRUDockTopPos are basically the Yorigin of the toolbar, with respect to the origin of it's Container when Docked. So it may be as simple as, there have been several programmers, over the years working on this feature, and it may be the ol' righthand/lefthand scenario.

SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK UPDATE

however, I noticed that some toolbars update both values, other toolbars do not. (Generally the MRU attributes are there to put a toolbar back where it was after it was turned off, and then turned on again.) I'm guessing a bit here. XPos and MRUDockLeftPos are basically the Xorigin of the toolbar, with respect to the origin of it's Container when Docked.

The toolbar registry entries do have XPos and YPos values, but I can't find a clear connection between them and the toolbar's actual position. I was hoping to see some way to detect and set a toolbar's (x, y) position. I have been opening and closing toolbars and sketchup all day, and can see no patterns. Each individual floating toolbar container is wrapped by it's own Framed Window (class 'Afx:00400000:8:00010011:00000000:00000000' aka 'CMiniDockFrameWnd'.) The Toolbar Containers do not have their own names, but instead assume the window caption of the last toolbar that was docked in the container.ĥ9393 (0xe801) = StatusBar ĥ9402 (0xe80a) = SceneTabs () Each floating toolbar (class 'ToolbarWindow32') is wrapped by it's own container (class 'AfxControlBar80u') all of whom share the ControlID 59423, but each has it's own WindowHandle. DON'T Rely on the ending numbers of Keynames! Check instead the value of the BarID attribute:ĥ9423 (0xe81f) = FloatingToolBarContainer (for ALL toolbars) Thomthom wrote:17 is main toolbarThe container window Bars seem to start around 17 but the numbers change dynamically between sessions. You may know most programs are installed in C: drive by default, and usually, Program Files for 64-bit programs and Program Files (x86) for 32-bit programs.If section has Bars, then it contains other toolbarsīar#x refer to another entry with that ID

SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK WINDOWS 10

Need to move program files to another drive Both of them are hard-wired into Windows and things can go wrong if they are not where they’re supposed to be. If you drag them to another location directly, most of the programs on Windows 10 or other systems may stop working or do not respond correctly. Thus, it's not safe to move program files to another drive. If possible, it's not suggested to move program files to a different drive. You can check if you are in the following situation and then decide if you have to do so.

SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK INSTALL

Situation 1: low disk space warning pop up several timesĪs time goes by, the system partition may run out of space owing to increasing programs, and the PC may slow down as well. The situation could be more severe if you install a large amount of software on the computer. Situation 2: SSD does not have enough space In this case, if you don't want to uninstall them, try to move program files and program files (x86) from C drive to D drive or other partition with enough space, then save the newly installed software to new partition instead of C drive.

Nowadays, it's not rare to migrate OS to smaller SSD and use it as storage. But the problem is SSD can be fulfilled quickly if you install multiple programs on it. #Sketchup make 2014 file location registry hack install

SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK FREE

Thus, some users may want to free up disk space of SSD or directly move program files and program files (x86) from SSD to HDD.

SKETCHUP MAKE 2014 FILE LOCATION REGISTRY HACK HOW TO

How to move programs files to different drive safely In this case, you have enjoy both advantages of SSDs and HDDs. If you are in one or two situations above, you may want to use a relatively safe method. Then, how to make it easily? You can choose to make a system image backup (if you want) with a free backup software, AOMEI Backupper Standard, for example. #Sketchup make 2014 file location registry hack how to Method 3: Move installed program to another drive using “Move” feature.Method 2: Move program files to different drive using mklink.Method 1: Migrate program files to another drive using Registry Editor.Thus, you can get the PC back to normal without downtime.Īfterward, you can feel free to try the following 4 methods to move program files to different drive, namely using Registry, mklink, Move, or App mover.